Manley Snapper 100 Watt Monoblock
£CALL per pair
Price inc vat
Manley Snapper Front Manley Snapper Right Side 
 

Product Details

In keeping with their snappy oceanic and generally fish related product names Manley's all-tube 100 watt monoblock called The Snapper.

A terrific design from Manley's Mitch Margolis features a quartet of EL34 tubes in a fully differential circuit topology, including the input (12AT7) and driver (7044) stages. The Snapper can be driven fully balanced all the way through via the XLR inputs. If you have balanced outputs on your preamplifier, the Snapper is the first Manley design to let you take advantage of this without additional balancing input circuitry or input transformers. Very cleverly, the unbalanced phono outputs can be used as alternatives with equally impressive results.

Biasing is easy with all measurement points and trims located on the top deck and speaker connection is made with heavy duty WBT binding posts.

Over three months of R&D in the Manley Magnetics department resulted in a brand new output transformer design, an incredibly complex 19-section piece. The Snapper will crank out 100 watts at 10 cycles all day long and a full 110 watts from about 15Hz all the way up to 40KHz. Some manufacturers will try and mislead you with frequency response specs. "Just listen to the amazing bandwith on our HokeyKokey 400BZX9" They don't tell you this may have been bandwidth measured at oh, 5 watts. Manley products are designed to deliver full power bandwidth. Continuous duty.Real muscle.

Technical Specifications

Input Impedance RCA: 475 Kohm
Input Impedance XLR: 15 Kohm or 600 ohm switchable
Input Sensitivity RCA: 750mV input = 110W output
Input Sensitivity XLR @ 15Kohms: 1.5 V input = 110W output
Input Sensitivity XLR @ 600ohms: 2.4 V input = 110W output (w/600ohm source)
Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB
Gain XLR: factory set for 25 dB
Negative Feedback: factory set for 9dB of global NFB
Maximum Output Power into 5 ohms: 110 Watts (1.5% THD @ 1kHz)
Maximum Output Power into 8 ohms: 100 Watts (1.5% THD @ 1kHz)
Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K
Noise Floor:
Typically 105µV = -77dBu A-WGT
Typically 388µV = -66dBu unweighted
Dynamic Range: 98dB
THD+noise @ 1W less than 0.1%
Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT
Frequency Response at 5W into 5 ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz
Recommended Speaker Load: Optimized for 5 ohms
Actual Output Impedance: 1.5 ohms
Power Consumption (idle): 170 Watts (1.4A @120VAC)
Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)
Vacuum Tubes: 1 x 12AT7WA Ei, 1 x 7044 GE JAN NOS,
4 x EL34EH Output
B+ Voltage: 570V DC
Output Tube Quiescent Standing Current: 30mA
Set Bias for 300mVDC measured across 10 ohm cathode resistor
Lamp type: "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs
Fuse types for
120VAC operation: MDL or MDA 4 AMP / 250 Volt SLO-BLO
240VAC operation: MDLor MDA 2 AMP/ 250 Volt SLO-BLO
B+ FUSE: MDA 4/10th AMP, 250 Volt SLO-BLO
Dimensions: 15" deep x 13" wide x 8.75" tall
Shipping weight each: 45lbs/20.4kgs

Owners Manual

Owners Manual Download Owners Manual

© Sable Marketing | Firemouth Web Design