Manley Mahi 50 Watt Monoblock
£CALL
Price inc vat
Manley Mahi Front Manley Mahi Right Side Manley Mahi Rear
 

Product Details

For those of you who get excited about tubes, here's some interesting spec. The MAHI produces around 40 watts RMS in Ultra-Linear mode or around 20 watts in TRIODE from a quartet of EL84 / 6BQ5 tubes driven by a 6414 dual triode driver and a 12AT7WA input dual triode. The Ei Yugo EL84 has been a Manley favourite for years. Long lasting and reliable, it can be considered the smaller brother of the much loved EL34: a great response with rich warm low frequencies and bright but un-fizzy natural sounding top end. The MAHI also uses the same output transformer as the Manley Stingray.

Manley have been building EL84 amplifiers for well over a decade. The Manley branded Tiny Triodes were much acclaimed by HiFi afficionados in the early 1990's. In 1993 after Manley split from VTL, the Manley Tiny Triodes underwent a chassis rework to become the Manley 35 watt Monoblocks soon followed by the 50 Watt Monoblocks. The more powerful Ultra-Linear mode operation became the standard with the hard-wired Triode operation or Triode/UL switching available upon special request.

After the introduction of the Stingray Integrated amplifier in 1998, it's new circuitry design refinements were incorporated into the 50 Watt Monoblocks. At last - big bass from a small amplifier! In essence, these post-1998 50 watt units were monoblock versions of the stereo Stingray, with the additional variable feedback feature. After the introduction of the Manley Snappers in 2002, Manley decided to update their classic EL84 50 watt monoblock units with a technical and cosmetic make-over.

Manley's response to constant requests for Triode/Ultra-Linear switching was to put the Triode-UL switch as standard for the new MAHI. They also added beautiful German WBT binding posts and significantly increased the B+ rail capacity. The 50 Watt monoblocks only had around 49 Joules or energy storage in the B+ rail. Now the MAHI's have nearly 180 Joules of energy storage for the B+ rail. You can really hear this improvement, especially in the bass region: tight, fast, deeper. More is more in this case.

The MANLEY MAHI's offer exceptional value for money we think you will be very pleasantly surprised at just how good they sound.

Technical Specifications

Input Sensitivity:

Input Impedance: 110 Kohm
TRIODE/UL
FB MIN: 175mV / 155mV
FB STD: 312mV / 340mV
FB MAX: 480mV / 566mV
Gain: 29dB
Negative Feedback: MIN= 3dB; STD=6dB; MAX=10dB of global NFB
Max. Output Power defined as power output reaching 1.5% THD @ 1KHz
into 5 ohms: TRIODE / UL
FB MIN: 18W / 20W
FB STD: 27W / 42W
FB MAX: 28W / 46W

into 8 ohms: TRIODE / UL
FB MIN: 14W / 24W
FB STD: 24W / 40W
FB MAX: 25W / 41W
Signal to Noise Ratio Ref. 1W: Typically 82 dB A-WGT 20-20K
Noise Floor: Typically 150µV = -74dBu A-WGT
Typically 650µV = -62dBu unweighted
Dynamic Range: 83dB
THD+noise @ 5W less than 0.15%
Frequency Response at full power UL mode w/MAX NFB: 20 Hz to 20 kHz FLAT
Frequency Response at 5W into 5 ohms: 10 Hz to 30 kHz FLAT, -3.75dB @ 100KHz
Recommended Speaker Load: Optimized for 5 ohms
Actual Output Impedance: TRIODE/UL
FB MIN: 2.83 ohms / 3.57 ohms
FB STD: 1.87 ohms / 2.16 ohms
FB MAX: 1.28 ohms / 1.36 ohms
Power Consumption (idle): 102 Watts (0.85A @ 120VAC)
Power Consumption (at Rated Full Power): 168 Watts (1.4A @ 120VAC)
Vacuum Tubes: 1 x 12AT7WA Ei, 1 x 6414 JAN NOS, 4 x EL84 Output per monoblock
Output Tube Quiescent Standing Current: 20mA
Set Bias for 200mVDC measured across each 10 ohm cathode resistor
Fuse types for
120VAC operation: MDL or MDA 3 AMP / 250 Volt SLO-BLO
240VAC operation: MDL or MDA 2 AMP / 250 Volt SLO-BLO
B+ FUSE: MDA 4/10th AMP, 250 Volt SLO-BLO
Dimensions: 11" deep x 10" wide x 5" tall
Shipping weight each: 18lbs/8.2kgs

Owners Manual

Owners Manual Download Owners Manual

© Sable Marketing | Firemouth Web Design